Warranty and billing
How do I separate warranty jobs from chargeable ones and bill only the out-of-warranty work?
Store warranty coverage on the asset, not on the job: an install date and serial number, then a start and end date for each kind of cover (manufacturer parts, your own labor warranty, any service contract). When a job is raised, compare the fault date with those dates and decide per line, because one visit is often part covered and part chargeable: the manufacturer replaces the failed part while the customer pays for labor, the trip and refrigerant. Bill each line to whoever owes it, the customer, the manufacturer or your own warranty cost, and send the customer an invoice for only the lines that are theirs.
- Coverage belongs to the asset and its serial number. A job only inherits it.
- Warranty is decided per line, not per job. Parts, labor, trip and consumables often have different answers.
- Every covered line still has a payer: the manufacturer through a claim, or your own warranty cost.
- Claims have deadlines. Lennox's basic warranty requires claims within 45 days of the component's failure date.
- If the fault is misuse or damage, the job turns chargeable on site, so the technician needs a quote flow on the phone.
This page covers the process and the records. What a specific warranty covers is set by its own terms and by consumer law where you work, so read the document for the product in front of you.
Facts checked as of November 2026. Sources at the end of the page.
Step by step
How separating warranty from chargeable work goes, step by step
There are three questions on every service call. Is this unit covered, by whom, and for what. The first two can be answered from dates before anyone drives to site. The third is answered by the technician, on the phone, in front of the unit.
1. Give every unit an asset record with a serial number
Model, serial number, site, install date, who installed it and the original job or sales invoice. Without a serial number and an install date there is nothing to check a warranty against, and no manufacturer will accept a claim.
2. Record each kind of cover as its own pair of dates
Most units carry more than one promise. A manufacturer parts warranty (often with longer terms for a compressor or heat exchanger). Your own labor or workmanship warranty on the install or the last repair. An extended warranty or a service contract the customer bought. Each one gets a start date, an end date and a short note of what it covers. One 'under warranty: yes or no' tick box cannot hold this.
3. Check cover when the job is created
The office picks the asset and the system compares the reported fault date with each end date. The job is tagged, e.g. Manufacturer warranty, Our warranty, Contract or Chargeable, and the customer is told what to expect before the visit: parts covered, labor and call-out payable, for example.
4. Let the technician confirm or overturn it on site
The technician sees the tag and the dates, checks the serial number on the nameplate against the record, and records a cause: defect, wear, misuse, physical damage, power or water quality, someone else's repair. A covered tag with an excluded cause turns the job chargeable, and the technician raises a quote on the phone for the customer to approve before work starts.
5. Decide each line, not the whole job
Every part and labor line carries a 'billed to' value: customer, manufacturer or internal warranty. A failed compressor can go to the manufacturer while three hours of labor, the trip charge and refrigerant go to the customer. This one field is what makes the invoice come out right.
6. Request the part and keep the failed one
A covered part is requested from the van, the stores or the distributor against the job, with the model and serial number on the request. The failed part is tagged with the job number and kept until the claim is settled, because the manufacturer may ask for it.
7. File the manufacturer claim from the job
The claim needs what the job already holds: model, serial number, install date, failure date, failed and replacement part numbers, the cause and the supplier invoice for the replacement part. Track it as its own record with a status (e.g. To file, Filed, Paid, Rejected) and the deadline.
8. Invoice the customer for their lines only
The customer invoice lists every line, shows covered lines at zero with the reason, and totals only the chargeable ones. Covered lines post to a warranty cost account or to the manufacturer's account, so the month's warranty spend is a number you can read.
The kinds of cover a single unit can carry at once. The terms in the right-hand column are examples read from the manufacturers' own published warranty pages in November 2026. Other products and brands differ.
| Kind of cover | Who pays | A real example of the terms |
|---|---|---|
| Manufacturer parts warranty | The manufacturer supplies or credits the part. The customer usually pays labor. | Trane's residential pages say the Base Limited Warranty covers parts that fail due to manufacturer defect but not the labor to repair them, and in most cases lasts five years. Registering within 60 days of installation gives the Registered Limited Warranty, in most cases 10 years. Under either, the owner is responsible for the cost of labor and shipping. |
| The same warranty on a commercial site | Often a much shorter term, so the install type has to be on the asset. | Lennox's Basic Limited Warranty covers listed components for five years in a residential application and one year in non-residential applications, with separate terms for compressors and heat exchangers. It does not cover refrigerant, refrigerant line sets, belts, gaskets, wiring or fuses, and trip charges and labor costs are the owner's. A replacement component does not extend the warranty period. |
| Your own labor or workmanship warranty | You do. It is a cost of the original job. | Set by your own terms, per job type. ServiceTitan's help gives the example of a 30-day recall period on service calls and a 90-day recall period on installations, and its equipment record has separate Manufacturer Warranty and Service Provider Warranty dates. |
| Extended warranty or service contract | The plan provider, or you if you sold the contract. | Trane says its Optional Extended Warranty, bought from the dealer, covers parts and might cover labor depending on the plan purchased. A maintenance contract you sell yourself works the same way: a list of what is included, with dates. |
Consumer law can sit on top of all of these. See the regional notes at the end of the page.
Failure modes
Why it goes wrong
Warranty is a job type, so the whole job is free
The head of service at a maker of industrial battery chargers and EV chargers asked whether warranty versus out-of-warranty could be classified and a parts request or quotation raised from the engineer's phone. That is the real requirement: the classification has to reach the line items. When warranty is only a job type, the labor, trip and consumables the customer owes are never billed. ServiceTitan's help describes its recall and warranty jobs as No Charge, Non-Convertible jobs, where the customer is not charged and the technician is not expected to sell an estimate, which suits a callback on your own work and suits a parts-only manufacturer warranty less well.
Nobody checks the dates until the invoice is disputed
The install date is on a paper file or the old job, so the office guesses. Either a covered customer is charged for a part and complains, or an expired unit is repaired for free. Registration matters too: on Trane's residential terms, a unit registered within 60 days of installation has cover for 10 years in most cases, and an unregistered one for five.
The manufacturer claim is never filed, or filed late
The technician fits a part from the van, the job closes at zero, and no one claims the part back. Lennox's basic warranty says all claims must be submitted within 45 days of the component's failure date and that a late claim is denied. A claim that depends on someone remembering is a write-off.
Claims are re-keyed into a portal and rejected for a missing field
The owner of a multi-trade appliance repair, electrical and air conditioning business, about 23 staff and 600 to 700 jobs a month, described warranty work as painful because of all the manufacturers and their portals. Each portal wants the same facts in its own layout. One appliance repair tool's checklist for claims sent to the ServiceBench portal requires the model number, serial number, purchase date, the part's invoice number and an explanation of service of at least 16 characters. A job closed without the serial number cannot be claimed.
One call involves three parties
A manufacturer that sells through OEMs and dealers has to track the OEM, the dealer and the end user on one complaint, and the party that owns the unit is not always the party that pays. If the job has only one customer field, warranty jobs get invoiced to the wrong account or not at all.
Warranty and contract visits are mixed up
A pump sales and service company asked whether service contracts and warranty or AMC visits could be managed together. They are different promises. A contract visit is prepaid maintenance. A warranty repair is a defect. A unit can be in both, in one or in neither, and each needs its own dates.
Options
Ways to do it
What each kind of tool does, as its own help pages describe it in November 2026. The split that matters: does cover live on the asset with dates, and does the tool act on it at the line level or only show it.
| Approach | What it does | Watch for |
|---|---|---|
| Spreadsheet of serial numbers plus a note on the job | An asset list with install and expiry dates, checked by hand when a call comes in. The technician writes 'warranty' on the job sheet. | Works for a few dozen units. Nothing stops an invoice going out wrong, and claims are tracked in someone's inbox. |
| A warranty expiry date on the asset (Zoho FSM) | Zoho FSM's help says an asset can hold an Ordered Date, Purchased Date, Installation Date and Warranty Expiry Date, so you can see whether it is under warranty. | One expiry date per asset. The help page describes tracking only and does not say work orders or invoices change when an asset is covered, so the billing decision stays with a person. |
| Warranty records mapped to assets (Dynamics 365 Field Service) | Warranties are separate records that an administrator enables, and each one is mapped to covered assets, locations or accounts. Microsoft's release note says frontline workers can see whether an asset is covered. | Microsoft's article says warranties are not tied to work orders, so pricing or discounts are not automatically applied on a work order. Someone still has to zero the covered lines. |
| Warranty and recall job types linked to the original job (ServiceTitan) | A recall or warranty job is booked from the original job and linked to it automatically. Both are No Charge, Non-Convertible jobs. The equipment record shows Manufacturer Warranty and Service Provider Warranty dates with the time remaining. | Built around callbacks on your own work. Ask how a visit that is part covered and part chargeable is invoiced, and where the manufacturer claim is tracked. |
| Trade software that submits claims to manufacturer portals (ServiceWorks, appliance repair) | Part billing and labor billing on a job are each set to the manufacturer the warranty work is for, and the claim is submitted to a claims processor such as ServiceBench or ServicePower from the job. | Made for authorized appliance servicers who are paid by manufacturers. Each manufacturer account number has to be set up, and a claim needs the model, serial number, purchase date and part invoice number on the job. |
| Field service software set up around your warranty rules (Fieldproxy) | Cover dates sit on the asset, the job is tagged when it is created, each line carries who it is billed to, and the claim is a record with a deadline. Statuses, forms and rules are configured to your own terms. | Fieldproxy applies the rules you give it. It does not hold manufacturers' warranty terms for you and does not file claims into third-party portals out of the box, so claim submission is a step your team does or an integration to scope. |
Vendor behavior changes. Ask each vendor to run one job on a unit that is in parts warranty but out of labor warranty, and to show the customer invoice and where the part claim went.
Worked example
A worked example
Say an air conditioning contractor replaces a failed compressor on a residential unit it installed six years ago. The unit was registered, so the manufacturer's parts warranty runs 10 years. The contractor's own labor warranty on the install was one year. The numbers are an illustration.
The job has four lines. The compressor costs $640 from the distributor. Labor is 3 hours at $140, so $420. Refrigerant is $180. The trip charge is $95. That is $1,335 in total.
Decided per line: the compressor is billed to the manufacturer, because the part is inside the 10 years. Labor is billed to the customer, because the one-year labor warranty ended five years ago. Refrigerant and the trip charge are billed to the customer, because the parts warranty does not cover them. The customer invoice shows all four lines, the compressor at zero with 'manufacturer warranty', and a total of $695. A claim for $640 goes to the distributor with the model, serial number, install date, failure date and both part numbers.
Now the two ways it goes wrong. If the job is booked as a warranty job with no charge, the contractor gives away $695 it was owed. If nobody checks the dates and the job is invoiced as chargeable, the customer pays $1,335 for a repair that should have cost $695, and finds out later.
Change one fact. The unit was never registered, so the parts warranty was five years and ended a year ago. Every line is now the customer's and the technician needs an approved quote for $1,335 before fitting the part. Same unit, same fault, a different invoice, and the only difference is one date on the asset record.
And the claim: if the manufacturer's terms give 45 days from the failure date, a compressor that failed on March 3 has to be claimed by April 17. A job that closes on March 4 with the claim still 'to file' needs to show up on a list before then.
Before you buy
What to check before you buy
Good signs
- An asset can hold several kinds of cover, each with its own start and end date, not one expiry date.
- The job shows the cover status when it is created and again on the technician's phone.
- Each part and labor line can be billed to the customer, the manufacturer or an internal warranty account.
- A technician can turn a covered job into a quote on site, with customer approval captured before work starts.
- A manufacturer claim is a record with a status, an amount and a due date, linked to the job and the failed part.
- The job cannot be completed without the serial number and a cause of failure.
- There is a report of warranty cost by product, by manufacturer and by technician, and a list of claims not yet paid.
- Warranty dates can be imported in bulk from your sales or install records.
Red flags
- Warranty is only a job type or a tag, and choosing it makes the whole job free.
- The only way to not charge for a part is to delete the line or discount it to zero by hand.
- Warranty dates are a note in a text field that nothing reads.
- The office can see cover but the technician cannot.
- Claims are tracked outside the system, in email or a spreadsheet.
- The vendor cannot show where the failed part's serial number is recorded.
In Fieldproxy
Setting it up in Fieldproxy
Fieldproxy is set up around your process, so the warranty rules are configured to your own terms and your manufacturers' terms. Settings marked e.g. are examples to change.
Assets with cover dates
Each asset record holds the model, serial number, site, install date and a QR code, plus fields for each kind of cover (e.g. Parts warranty until, Labor warranty until, Contract until, Registered yes or no, Residential or commercial). Assets and dates are imported in the free, assisted migration from your sales, install or old service records. See /solutions/asset-management.
A cover status on every job
When a job is created against an asset, a rule compares the reported date with the cover dates and sets a field (e.g. Manufacturer warranty, Our warranty, Contract, Chargeable). The office sees it on the job and the technician sees it in the Android or iOS app before leaving for site.
The nameplate read from a photo
On site, the technician photographs the nameplate and the Vision agent (/agents/vision-agent) reads the model and serial number into the job, so it can be matched to the asset record. A mismatch (e.g. a unit swapped since install) is flagged before any free work is done.
Cause of failure and a billed-to value on each line
The job form has a required cause field (e.g. Defect, Wear, Misuse, Damage, Third-party repair). Each part and labor line carries a billed-to value (e.g. Customer, Manufacturer, Internal warranty), defaulted from the cover status and changeable by the technician with a reason. A job cannot move to (e.g.) 'Ready to invoice' until both are set.
A quote from the phone when it is not covered
If the cause is excluded or the dates have passed, the technician builds a quote in the app from the price book and the customer approves it on a link or with a signature. Approval workflows (/solutions/approval-workflows) can route quotes above an amount (e.g. $500) to a manager first. Covered parts are requested against the job from van stock or the stores; see /solutions/spare-parts.
Claims as their own records
A manufacturer claim is created from the job with the model, serial number, install and failure dates, part numbers and photos already filled in, and a due date worked out from your rule (e.g. failure date plus 45 days). The Watcher agent (/agents/watcher-agent) flags claims close to the deadline and covered jobs closed with no claim. Autopilot (/agents/autopilot) drafts the chase for unpaid claims for a person to approve.
Invoices and reports
The customer invoice shows covered lines at zero and totals the chargeable ones, then syncs to QuickBooks or Xero with the accounts you map at setup (e.g. warranty cost, manufacturer receivable). In the Command Center (/agents/command-center) you can ask for this month's warranty cost by product or the claims still unpaid. One price per company with unlimited users, so stores, logistics and approvers do not need paid seats; see /pricing.
Regional notes
What the law adds, by country
The warranty document is not always the last word on whether a repair is chargeable. These points apply to consumer sales. Commercial customers are mostly governed by the contract.
United States
Under the Magnuson-Moss Warranty Act, a warrantor cannot make a written or implied warranty conditional on the consumer using a part or service identified by brand, trade or corporate name, unless that part or service is provided free under the warranty or the FTC grants a waiver. To meet the federal standards for a full warranty, the warrantor must remedy a defect within a reasonable time and without charge. Most equipment warranties in the trades are limited warranties, which is why labor is usually payable.
United Kingdom
GOV.UK's guidance for businesses says a customer has the same right to free repairs or a replacement whether or not they have a warranty or guarantee, so you may still have to repair or replace an item after the warranty has run out. You must repair or replace an item returned within 6 months unless you can prove it was not faulty when bought, and customers have up to 6 years to make a claim (5 in Scotland).
Australia
The ACCC says warranties are offered in addition to consumer guarantee rights and cannot replace, change or take away those rights. After a warranty expires, the consumer guarantee of acceptable quality usually still applies. So 'out of warranty' on the asset record is a prompt to check, not an automatic chargeable job.
How switching works
How switching to Fieldproxy works
We move your data over and set the system up to the way you already work. Fieldproxy replaces the old tool; it does not run alongside it.
Bring your warranty terms and three jobs
Your own labor warranty terms, the manufacturers you service with their claim rules, and three real jobs: one fully covered, one part covered, one you billed and later had to credit.We set up cover dates and the billed-to rule
We configure the cover fields on the asset, the status on the job, the cause list and the billed-to value on each line to match how you decide today.Assets and serial numbers come across
Customers, sites, assets with serial numbers and install dates, open jobs, contracts and price lists move over in a free, assisted migration. Units with no install date are listed for you to fix.Test the three jobs, then go live
The three jobs are run again and the invoices and claims checked against what you expected. Live within a day: technicians get the Android or iOS app and the office invoices from the job.
FAQ
Questions people ask
- Can warranty versus out-of-warranty be classified from the engineer's phone?
- Yes, if cover dates are on the asset and the app shows them on the job. The technician confirms the serial number, records the cause, and each line is set to customer, manufacturer or internal warranty. If the job turns out chargeable, a quote is raised on the phone for approval before the repair.
- How do I bill a job that is part warranty and part chargeable?
- Put everything on one job and decide per line. Covered lines show at zero on the customer invoice with the reason, chargeable lines are totaled, and the covered part goes on a claim to the manufacturer or distributor. Two separate jobs for one visit make history harder to read.
- Does a manufacturer's warranty cover labor?
- Often not. Trane's residential pages say its Base and Registered Limited Warranties cover parts but not the labor to repair them, and Lennox's basic warranty leaves trip charges and labor costs with the owner. An extended warranty may add labor. Read the terms for the product.
- What do I need to file a manufacturer warranty claim?
- At least the model, serial number, install date and a description of the problem. Lennox's warranty lists the model and serial number, the owner's name and equipment location, the original installation date and an accurate description of the problem. A distributor's HVAC claim form such as Ferguson's also asks for the failure date, the failed and replacement part numbers, the reason for failure and the invoice number of the replacement part.
- Can field service software manage service contracts and warranty or AMC visits together?
- Yes, as separate things on the same asset. A contract creates planned visits and lists what is included. A warranty has dates and covers defects. The job checks both, so a contract visit is not billed and a breakdown outside both is.
- How do I track the dealer, the OEM and the end customer on one warranty call?
- Keep three links on the asset or job: who owns and uses the unit, who sold it, and who pays for this repair. The site and contact come from the end user, and the billed-to value on each line decides whether the invoice or claim goes to the dealer, the manufacturer or the user.
- Does a replacement part restart the warranty?
- Not usually on the equipment. Lennox's basic warranty says installing a replacement component does not extend the warranty period of the equipment it is fitted to. Your own labor warranty on the repair is a separate promise, so record it as a new date on the asset.
- Can AI handle the manufacturer warranty portals for us?
- It can do the preparation: read the nameplate from a photo, check the dates, fill the claim record and flag missing fields or a deadline. Submitting into each manufacturer's portal depends on that portal. Some claims processors accept claims from connected software and others need a person to key them in.
Sources
Competitor details on this page come from the vendors' own pages and documentation, checked as of November 2026. Plans and prices change, so check the vendor's current page before you decide.
- Trane: Warranty and registration: https://www.trane.com/residential/en/for-owners/warranty-and-registration/
- Lennox: Equipment Basic Limited Warranty (W900000): https://www.lennox.com/dA/7489c121a9/W900000-02e.pdf
- Ferguson: Submit an HVAC warranty claim: https://www.ferguson.com/content/customer-support/warranty-information/hvac-warranty/
- ServiceTitan Help: Book a recall or warranty job: https://help.servicetitan.com/docs/book-a-recall-or-warranty-job
- ServiceTitan Help: Track and manage installed equipment: https://help.servicetitan.com/docs/track-manage-installed-equipment-1
- ServiceTitan Help: Set recall, warranty and lead job booking guides: https://help.servicetitan.com/commercial/docs/set-recall-warranty-and-lead-job-booking-guides
- Microsoft Learn: Create warranties and define coverage (Dynamics 365 Field Service): https://learn.microsoft.com/en-us/dynamics365/field-service/warranties
- Microsoft release plan: extended customer details and manufacturer warranties: https://learn.microsoft.com/en-us/dynamics365/release-plan/2023wave2/service/dynamics365-field-service/expedite-service-delivery-extended-customer-details
- Zoho FSM help: Does Zoho FSM allow asset warranty tracking?: https://help.zoho.com/portal/en/kb/fsm/faqs/asset-management/articles/does-zoho-fsm-allow-asset-for-warranty-tracking
- ServiceWorks: Warranty claims, a step by step guide: https://blog.service.works/tutorial/warranty/warranty-claims-in-serviceworks-a-complete-step-by-step-guide/
- ServiceWorks Help: Prerequisites to submit a claim at ServiceBench: https://help.service.works/Integration/Warranty_Claim/ServiceBench/Pre-requisites_to_submit_claim_at_ServiceBench.htm
- 15 U.S.C. 2302: Rules governing contents of warranties (Magnuson-Moss): https://www.law.cornell.edu/uscode/text/15/2302
- 15 U.S.C. 2304: Federal minimum standards for warranties: https://www.law.cornell.edu/uscode/text/15/2304
- GOV.UK: Accepting returns and giving refunds: https://www.gov.uk/accepting-returns-and-giving-refunds
- ACCC: Warranties: https://www.accc.gov.au/consumers/buying-products-and-services/warranties
Related
Keep reading
- Service history per asset with QR codes
- Maintenance contracts that create the next visit
- Van stock and parts used on jobs
- Technician quotes with manager approval
- What is the best field service software for a 5-10 person HVAC team?
- Cheaper ServiceTitan alternatives for small plumbing and HVAC companies, without payment processor lock-in